I have been looking everywhere for a M16A4/ACOG TA01NSN 4×32 standard GI 25meter zero target. I have seen them online but can’t find. Designed for the M4/M16A4, the ACOG provides an “auto ranging” reticle for ranges When a target is acquired, use the ranging reticle (if time allows) to get an Without the aid of references, demonstrate the two methods to zero the ACOG. feedback (Figure 10). The M Sight, RCO, when installed on a M4/M4A1/ M16A4/M16A2, is zeroed on a standard M16 zero target with alternate strike points.
|Published (Last):||24 March 2004|
|PDF File Size:||3.82 Mb|
|ePub File Size:||4.28 Mb|
|Price:||Free* [*Free Regsitration Required]|
Rotate the borelight back to the start point; move the zeroing mark to the visible laser. Dench, I got to play with the file you sent me and with the one in PDF.
The soldier must keep the rifle and M68 in a vertical alignment each time he fires. The night sustainment training strategy zeero for soldiers who are familiar with night vision goggles, and for units that have already implemented a night-training program. Before beginning a night marksmanship program, soldiers must qualify on their assigned weapons during daylight conditions as outlined in the previous chapters of this manual. Couldn’t be any easier.
ACOG zeroing question | Lightfighter Tactical Forum
Zeroing at 25 meters must be conducted to ensure the TWS is properly zeroed. Also, sighting in a super short range like 25 or 33 amplify any errors made and mismatch in design parameters sight picture consistency, actual distance between target and firer The integrated act of firing with the M68 is identical to the iron sights except for yarget change in targget picture.
Two soldiers a firer and a target holder are required to properly boresight a weapon. Soldiers must qualify on their assigned weapons during daylight conditions as outlined in this manual. This fundamental is not affected by night firing conditions using the TWS.
The M68’s reflexive sight allows the soldier to fire the weapon with his cheek at a comfortable position; however, the soldier must zero with the same cheek position he will fire with because the parallax free is only effective beyond 50 meters. Use the same procedures and standards as with the iron sights along with the following.
When cutting the 3-centimeter square out of the target, some of the strike zone may be cut out. When the line aligns with the shoulder width of your target you should hit it.
The visible laser of the borelight is aligned with the barrel of a designated weapon. The procedures for record qualification are:.
How to Zero an ACOG Sight
There is bullet drop in game. Regular blinking must be reinforced during training. Since the TWS detects thermal energy heat emitted from an object, a position near an object emitting a vast amount of thermal j4 for example, a vehicle with the engine running, a fire, or so on may affect the soldier’s ability to acquire a target.
If the weapon is boresighted using field-expedient methods sandbags, rucksacks and the weapon is laid on the side for stability, ensure that the boresight target is also oriented in the same manner.
PNov 2, Where do you aim with the ACOG? The backup iron sight BIS is a semi-permanent flip up sight equipped with a rail-grabbing zerl. Oct 17, Messages: Both the narrow and wide field of views must be boresighted and zeroed. Taret the dry-fire exercise soldiers acquire a sight picture on all exposed silhouette targets prior to conducting the field-fire scenario.
FM Chapter 8 Advanced Optics, Lasers, And Iron Sights (Phase V of
I aim between the ironsight and the chevron. Jun 21, Messages: Question for those who might know. DenchMay 17, This chapter implements new night qualification targeh to compliment current Army training strategies.
Qualification standards are the same for day and night. The gunner must practice raising his head just enough to clear the weapon with his NVGs and acquire a good sight picture by walking the laser onto the target and then aiming at center mass. So, your point of aim would be the center of the main crosshairs and you would adjust elevation top screw.
The night vision devices have a degree field of view, which causes the average shooter to miss easy targets of opportunity.