HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit. Robokits India HT12E & HT12D Encoder and Decoder IC for RF Modules [RKI- ] – The HT 12E Encoder ICs are HT12E Datasheet · HT12D Datasheet.
| Author: | Goltizshura Sarr |
| Country: | Iran |
| Language: | English (Spanish) |
| Genre: | Marketing |
| Published (Last): | 11 June 2010 |
| Pages: | 196 |
| PDF File Size: | 16.76 Mb |
| ePub File Size: | 18.1 Mb |
| ISBN: | 834-6-39387-702-8 |
| Downloads: | 92618 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Negis |
To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.
Connected to the Ground of circuit. Mercury ball tilt switch 5mm dia. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.
HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet
These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. They are paired with 2 12 series of decoders for use in remote control system applications.
We should set the bits in same pattern on Encoder and Decoder IC to pair them. If any valid data is received they can be obtained from these four pins. Connected to the Ground of circuit. Pull the Transmission Enable pin pin 14 to ground to activate transmission.
The IC has a built in fatasheet. SPI Module of Arduino. You can know to set up the HT12D after this from here. They can also be connected to LED to physically view the received data. Can range from 2. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. These are the 8-bit address bits, which is used to protect your data.
The encoded bit can be obtained from the Dout pin pin Submitted by admin on 30 October The IC is has a wide range of operating voltage htt12d 2. Skip to main content.
This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. Found this item with same quality and at a lower price but prefer to buy from robokits. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin ajd go high when a data is received. It is not mandatory to use it.
HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. The primary function of HT12E is to encode a bit jt12e send it out through the output pin.
HT12E Encoder IC
For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm ht12v, Smoke or Fire alarm system etc. This high-density System-in-Package SiP integrates controller, power switches, and support components. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.
These are the 8-bit address bits, which is used to protect your data. HT12E has a transmission enable ut12e which is active low. TL — Programmable Reference Voltage. These 12 bits are divided into 8 address bits and 4 data bits. Interface GPS with Arduino. These two ICs together form an Encoder and Decoder pair. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.
Be the first to write a review. They are capable of Encoding 12 bit of information which consists of N address bits and N data bits. We should set the bits in same pattern on Encoder and Decoder IC to pair them. Full Name Email Address. TL — Programmable Reference Voltage.
The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded.
In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. This pin will go high when a data is received.
Submitted by admin on 27 October Easy Interface with and RF or an Infrared transmission medium. These two ICs together form an Encoder and Decoder pair. It is very important that your Decoder should have the same address of that of the encoder. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. Easy to Use, Versatile Robotics Kits This oscillator can be used by connecting these two pins through a 1M Resistor.
If you want security you can connect any of the 8 pins to 5V to make it high. Customers who bought this product also purchased Interface SD Card with Arduino.