ASTM & ASHTO Tests. • 3). Why So Many Sealants. • 4). . ASTM. 5 specifications for Crack Seal. • ASTM D • ASTM D Type I. • ASTM D Type II. CrackMaster™ Type I. The ideal product for the contractor who wants a single product to use in both road and parking lot applications. Meets ASTM D Designation: D – 07Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements.
|Published (Last):||26 September 2008|
|PDF File Size:||8.65 Mb|
|ePub File Size:||3.76 Mb|
|Price:||Free* [*Free Regsitration Required]|
Mixing Procedures Use material as supplied.
Solution Center Common Problems. Coverage Use the following chart as a guideline for estimating material requirements based upon pounds of material needed for feet of cracks: Actual material usage may vary due to width of application and thickness of material above pavement surfaces.
Hard hat with face shield; long sleeved shirt buttoned at the wrist; heat resistant gloves; long, cuffless pants; and safety toed work boots. CrackMaster Type I forms a lasting seal that resists tracking in warm climates. You are using wstm outdated browser that does not support modern web site design.
Use the following chart as a guideline for estimating material requirements based upon adtm of material needed for feet of cracks: Company About Us Jobs. Though necessary, these cuts create a penetration point for water that needs to be sealed to prevent damage to the road base. Brands Elastoflex Nuvo Gap. This abstract is a brief summary of the referenced standard.
CrackMaster™ Type I – SealMaster
When concrete roads are poured, it is important that transverse and longitudinal joints be cut while the concrete is still green in order to control where the concrete cracks. It is ideally suited for both roadways and parking lots.
Support Solution Center Contact Ast. Compare to my climate.
How to fix a pothole How much does it cost to fix a pothole? When melted and properly applied it forms a resilient crack sealant for both asphaltic and cementatious pavements. The extremely hot material will cause severe burns on contact with skin. This specification covers four types of joint and crack sealants of the hot applied type intended for use in sealing joints and cracks in Portland cement concrete and asphaltic concrete pavements.
Nuvo Spec Best Performance. Sizes Available 50 lb. Joint Sealants When concrete roads are poured, it is important that transverse and longitudinal joints be cut while the concrete is still green in order to control where the concrete cracks. Use material as supplied. World-Class pavement maintenance products.
CrackMaster™ 6690 Type I
Using a sealing shoe or squeegee, band the material 2 to 3 inches wide over the crack. D690 Polyskin ZipBox Intelibond.
The ideal asttm for the contractor who wants a single product to use in both road and parking lot applications. Elastoflex 71 Best Performance. Clean Up Wash tools in water before material dries. Asphalt Pavement Concrete Pavement. How often should you sealcoat a parking lot or driveway?
Do not blend with other materials. Elastoflex 61 Best Performance. For best results the sealant depth to width ratio should not exceed 2 to 1 i. While there are many types of sealants, some of the most effective are hot-pour, asphalt based sealants. Maxwell Products manufactures several hot-pour sealants well suited for use in concrete joints that meet or exceed the relevant industry standard specifications.
It is informational only and not d660 official part of the standard; the full text of the standard itself must be referred to for its use and application. Elastoflex 51 Best Performance. Historical Version s – view previous versions of standard. The above coverage d66990 are only a guideline.
World-Class pavement maintenance products.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
Use with adequate ventilation. Link to Active This link will always route to the current Active version of the standard.
The sealants aatm be sampled and tested appropriately to examine their conformance with specified values of the following requirements: We recommend updating your browser as soon as possible. No other units of measurement are included in this standard.